Projects by type and sector.
50 engineering projects, each led by Syed Nasir, Lead Consultant and Founder. Find one like yours.
Which industry are you in?
What kind of project is it?
Delivered work.

Cryogenic LNG Pipeline Stress Analysis and Support Redesign at −162°C
CAESAR II stress analysis of a 2-inch stainless LNG line at −162°C feeding flow meters and a cryogenic pump, rerouted and re-supported to pass ASME B31.3.

6-Inch Natural Gas Line Stress Analysis from Measuring Station to Gas Dryer
Existing-versus-modified CAESAR II analysis of a 6-inch carbon steel gas line with buried branches, bringing all stresses within ASME B31.3 allowables.

Seismic Pipe Stress and API-617 Compressor Nozzle Assessment for a Refinery Upgrading Project
Seismic and static analysis of a 6-inch refinery line where one added support brought compressor nozzle loads from fail to pass under API-617.

Buried and Above-Ground Oil Pipeline Stress and Surge Analysis from Tanker Berth to Terminal
Static and surge analysis of a 406 mm buried and above-ground oil pipeline from a tanker berth to a terminal, with all cases passing BS EN 13480-3.

PED-Compliant Diesel Injection Skid Pipe Stress and Skid Frame Design
Turnkey diesel injection skid for Sites SRL, Italy: pipe stress analysis, pump nozzle loads and skid frame design to PED 2014/68/EU.

High-Pressure CO2 Metering Skid Pipe Stress Analysis and Skid Design
CAESAR II stress analysis to ASME B31.3 and skid structural design for a high-pressure CO2 metering skid for Sites SRL, Italy.

Horizontal Lifeline Fall-Arrest Design for an Oil Terminal Loading and Decanting Gantry
CSA Z259.16 horizontal lifeline design for PSO's KTB loading gantry: 10 m span, 6 kN arrest force and 2.145 m fall clearance below lorry height.

Multi-User Horizontal Lifeline Design for a Tank Lorry Loading Facility
Single- and two-user horizontal lifeline analysis to CSA Z259.16 for a 16.8 m span over a tank lorry platform, with 80.3 kN governing anchorage load.

Retractable Fall Protection for Loading and Decanting Gantries at an Oil Terminal
Retractable fall protection with structural anchorage design and SWL certification for loading gantries at Total Parco's Keamari Terminal, Karachi.

Six-Tank API-650 Design Calculation Package for a Refinery at Korangi, Karachi
API-650 design of six utility and process tanks (45.6 to 1,160 m³) for National Refinery and OGDCL, for wind up to 160 mph and seismic zones 2A/2B.

API-650 Design of a 60 ft Hot Asphalt Storage Tank (3,362 m³)
Full API-650 calculations for an 18.3 m diameter asphalt tank at 150°C design temperature, SG 1.06, 100 mph wind and seismic zone 2B.

Foundation Design for a 60 ft, 3,673 KL Furnace Fuel Oil Tank at a Refinery
Pile/raft foundation design for a new 60 ft diameter, 3,673 KL FFO storage tank at Attock Refinery.

Refinery Steel Structure Design and Vetting: Gantry, Flare Stack Anchors and Waste Heat Recovery Boiler
Structural vetting and design at Pakistan Refinery Ltd. (PRL): JP-1 gantry, flare stack anchor bolts, a waste heat recovery boiler structure and more.

FRP Wet Chlorine Line Material Upgrade and Integrity Assessment
Material selection, FEM thickness design and thermal analysis for upgrading a 100°C wet chlorine FRP line at Engro Polymer & Chemicals.

Low Grade Refining Column Design with 14 Bubble Cap Trays for Alcohol Distillation
EN 13445/ASME design of a 700 mm SS 304L alcohol refining column with 14 bubble cap trays, rated −1 to +3 bar g at 127°C.

Cryogenic Heat Exchanger Mechanical Design at −110°C and 112 bar
PV Elite 2019 design of heat exchanger HE-204 to ASME VIII Div.1: −110°C both sides, 112 bar channel, 19 load cases and TEMA tubesheet checks.

Steel Structures for a 65 KLPD Ethanol Fermentation and Distillation Plant
Design and detailed engineering of fermentation and distillation steel structures and civil foundations for a 65 KLPD ENA ethanol plant at Chashma.

Pipe Stress Analysis for a Large Water Treatment Plant with Pipe Sizes to DN1600
AutoPIPE stress analysis to BS EN 13480 across all piping systems at Thames Water's Becton plant, with pipe sizes up to DN1600.

Structural Analysis of a Power Plant Main Boiler Stack
Static and dynamic structural analysis of the main boiler stack at Saba Power Plant, Farooqabad, to AISC, with stress analysis of the stack piping.

IFC Package for Water Reservoir Modifications at a Power Plant
Condition assessment, modification design, specifications and BOQ for water reservoirs at Sindh Nooriabad Power Company (SNPC), issued as an IFC package.

Seismic Pipe Stress Analysis of a Data Centre Drainage Riser and Level Pipework
BS EN 13480-3 stress analysis of a Frankfurt data centre drainage riser in Seismic Zone 4, with peak stress at 9.1% of allowable.

Chilled Water Pipe Stress Analysis up to DN1000 for Microsoft MS-LON1
Lead pipe stress analysis, as subcontractor, of CHW piping up to DN1000 for Microsoft MS-LON1, with a friction factor study for product selection.

Antenna Support Structure Wind Load Analysis and AISC 360-16 Code Check
MIDAS/Civil analysis of a two-antenna steel mount in Amarillo, Texas, for 108 mph wind: maximum stress ratio 0.336 and deflection 0.318 in.

Building Services Pipe Stress Analysis for the Everton Stadium Project
White-label subcontract pipe stress analysis for the Everton Stadium project: mechanical, domestic and gas piping across movement joints up to 120 mm.
Pipe Stress Analysis of Plantrooms and 34-Floor Risers in a London Office Tower
Lead pipe stress analysis for The Leadenhall Building, London: plantrooms, floor pipework and risers to 34 floors, with support loads marked on drawings.

Large-Span Aluminium Trilite Space Frame Analysis for Event Use
STAAD.Pro analysis of a 2,380-node aluminium Trilite space frame under dead and wind loads, forming the basis for safe working load certification.

Steel Warehouse Structural Design with Fabrication-Ready DXF and 3D Model
Full steel warehouse design with Forge Steel, delivered as a fabrication-ready DXF and GLB 3D model for the steelwork contractor.

Multi-Floor Hotel Drainage Design with Backflow Protection and Fire Collars
BS EN 12056 drainage design for Baltic Hotel, Liverpool, from basement to 6th floor+, with SVP routing, backflow protection and FD60 fire collars.

Retail Tenant Improvement Permit Drawing Set in Albuquerque, New Mexico
PE-stamped tenant improvement permit set (G001 to M101) for a licensed dispensary in Albuquerque, submitted to the City in July 2025.

Full Construction Set for an R-4 Group Home in Lowell, Indiana
40+ sheet architectural, structural, MEP and fire protection set for an 8,250 SF R-4 group home, sealed in May 2019.

Chilled Water Fan Coil System Design for a 832-Occupant Workers Building in Abu Dhabi
Carrier HAP load analysis and 2-pipe fan coil sizing for a 7,212 m² G+3 workers building in Abu Dhabi: 651.4 kW coil load, 28.06 L/s chilled water.

Commercial Kitchen and Café HVAC Mechanical Drawings for a Mixed-Use Centre
Kitchen exhaust, make-up air and café HVAC drawing packages to NFPA 96 for IBL's One IBL Centre, issued across 2022 and 2023.

Hospital Pipe Stress and Acoustic Analysis for Plantrooms and Floor Pipework
Stress and acoustic analysis of mechanical and domestic piping at Midland Metropolitan University Hospital to reduce noise in a hospital setting.

Cooling and Heating Load Analysis for a University Building with a Glass Dome
Space-by-space Carrier HAP loads for 14 zones at SIUE, including an equivalent-volume glass dome model: 180,179 Btu/hr cooling, 8,500 CFM.

11 kW Rooftop Solar PV Design for a University Engineering Department
HelioScope design of a 10.8 kWdc system for NED University's Mechanical Department: 17.65 MWh a year against a 12.77 MWh load, PR 82.8%.

1.3 GWac Utility-Scale Solar PV Plant Design in Colorado
RatedPower design of Inovateus Solar's 1.33 GWac Kendall Ranch: 151 power stations, 40,678 trackers, 3.41 TWh in year 1 and PR 87.03%.

41.6 GWh Commercial Solar Plant Energy Yield Simulation in PVSyst
PVSyst v7.4.8 simulation for the TCP Godowns solar plant: 41.6 GWh a year to grid, P50 1,724 kWh/kWp and PR 82.29%.

296 kW Elevated Commercial Rooftop Solar PV Design
PVSyst-simulated 296 kW elevated rooftop system with 501 × 590 W modules on chemically anchored steel structure, plus layout and wiring drawings.

Primavera P6 Schedule for an 8.26 MW Factory Rooftop Solar PV Project
Activity-level Primavera P6 schedule for Gul Ahmed DCM Factory 01's 8.26 MW rooftop solar, tracking 42.94% progress against a 35.22% baseline.

S-Curve Progress Monitoring for a Wind Power Station
Planned-versus-actual S-curve reporting for a wind power station, showing 37.40% actual against 36.06% planned in April 2024.

32 m Electric Catamaran Passenger Ferry Concept Design for Lagos
DNV-compliant 200-passenger, 100% electric catamaran ferry for Lagos Lagoon: 17 knots service speed, 62 km range. Finalist in the WFSA competition.

1,000 m³ Split Hopper Barge Design and Class-Approved Construction
Full naval architecture and fabrication of a 1,000 m³ split hopper dredging barge in Karachi, with first-time class approval and no structural revisions.

CFD-Optimised Hull Design for a High-Speed Fast Response Boat
CFD hull optimisation, Maxsurf resistance checks and FEA for a security and emergency fast response boat, validated without a physical prototype.

LS-DYNA and RADIOSS Crash, Rollover and NVH Solver Correlation Study
The same crash, rollover, NVH and suspension cases run in LS-DYNA and RADIOSS to confirm solver equivalence and speed up design iteration.

Electric Formula Student Car Design: Chassis, Suspension and Drivetrain
Complete SAE-compliant electric formula car for NED-UET: AISI 1020 space frame with bending FOS 4.0, topology-optimised bell cranks, 312 Nm drivetrain.

Composite Overwrapped Pressure Vessel FEA Across 12 Load Cases
ANSYS assessment of a carbon fibre COPV to ANSI/AIAA S-081B-2018 for proof, burst, vacuum and thermal cases, defining redesign before flight approval.

Blast Shelter Explicit Dynamics Analysis Under Detonation Loading
ANSYS Explicit Dynamics simulation of a 5 m blast shelter under detonation, identifying failure zones (minimum safety factor 0.339) for redesign.

Aluminium 6061 Trailer Structural FEA for Static, Dynamic, Braking and Turning Loads
ANSYS FEA of a 7×12 Al 6061 trailer across four load cases: all passed (minimum FOS 1.255), with critical joint and weld recommendations.

CFD Feasibility Study of a Grease Distribution Network for Bearing Lubrication
Transient ANSYS Fluent study showing a proposed grease network could not reach its four bearings, with redesign recommendations before fabrication.

96-Inch Cone-Cylinder Carbon Steel Pressure Vessel Analysis in PV Elite
ASME VIII Div.1 analysis of the 96 in OD SA-36 DF-3 vessel with cone-to-cylinder transitions, ASCE-7 wind and UBC seismic, MDMT 20°F.
Companies we work for directly.
Alongside the projects above, many delivered as engineering subcontractor, Fluxiss works directly for these companies.
- Abuwandi Engineering Associates
- Condor Building Contracting LLC
- Diva Naval
- DreamerBoy Space Technology
- Eman Maqbool Mughal Contracting Est.
- Forza Group
- GAFT NORD AB
- Godela.ai
- Gulf Specialist Inc
- IDMC Pte Ltd
- Infofabs
- NextGen Steel
- nVent - LENTON
- Peace Core Group
- ProWise Group Inc.
- R-Stud – Sustainable Framing, LLC
- Recreation By Design
- Salama Engineering KSA
- SBT Pro
- THKN Services
- Sites SRL (Italy)
- ZEECO
Let's Build Something Great Together.
Partner with Fluxiss for engineering that holds up - under pressure, under load, under scrutiny.